<mark id="j7lnh"></mark>
<mark id="j7lnh"><video id="j7lnh"></video></mark>

    <cite id="j7lnh"><em id="j7lnh"><menuitem id="j7lnh"></menuitem></em></cite><cite id="j7lnh"><span id="j7lnh"><menuitem id="j7lnh"></menuitem></span></cite>

      <cite id="j7lnh"></cite>
      <cite id="j7lnh"><em id="j7lnh"><font id="j7lnh"></font></em></cite><cite id="j7lnh"><em id="j7lnh"><font id="j7lnh"></font></em></cite>

      <var id="j7lnh"><strike id="j7lnh"></strike></var>

      <mark id="j7lnh"></mark>

      歡迎訪問儀器儀表使用說明頻道HART375E手持器說明書(全英文)頁,專注打造儀器儀表行業知名平臺!

      儀器儀表公司

      當前位置:首頁 > 技術 > 使用說明

      HART375E手持器說明書(全英文)

      更新時間:2022年12月01日

      使用介紹

      QUICK GUIDE

      ◆Onoff Key

      The On/off Keyis used to power on and off Field Communicator by pressing it for one second.爭Up/Down Arow Key

      The two keys allow you to move up and down through the menu or option list

      Left/Right Arrow Key

      The left key ( allowsyou to move the cursor left or back to the previous menu while the keys "F4*" is shown

      on the screen.The right keyallows you to move the cursor right or select an item from the menu while the keys "F4*" isshown on the screen

      Enter KeyThe enter key  allows you to perform the focused item while keys "F4*" is shown on the screen.Tips: The so-called "F4" keys are soft input buttons(less than four) showing at the bottom of the screen duringoperat1on.

      There are usually four forms of the soft input buttons, they are "ABORT", "ESC", "ENTER", "BACK", "DEL'Alphanumeric and Shift Key

      The 12 alphanumeric keys in the middle of the keyboard allow you to input data. With other 3 shift keys at thebottom of the keyboard, you can input both letters and special characters. (Press a shift key first and then a key witha letter to input the letter. Don't need to press two keys at one time)

      BASIC FUNCTIONS (ONLINE SITUATION)

      Viewing Variables (Reading Values)

      Press key "l" to enter into "Process Variables"

      Setting Primary Variables Unit

      Press key"4.2.1" in turn to enter into"1 PV Unit'

      Setting Upper Range Value

      Press key "4, 2, 2" in turn to enter into "2 PV URV"

      Setting Lower Range Value

      Press key "4, 2,3" in turn to enter into "3 PV LRV"

      Setting Damping

      Press key "4,2,4" in turn to enter into "4 PV Damp"

      Analog Output Calibration

      Press key "2,3, 2" in turn to enter into "2 D/A trim"Note: The incorrect usage of analog output calibration is likely to increase the output error of the HART? device

      Primary Variables Zero TrimPress key "2, 3, 3, 1" in turn to enter into "1 Zero trim" (some devices may not have this function).Note: The function of primary variables zero trim can fix output zero bias of the instrument caused by installationpos1t1on.

      Normally the function can be performed just when HART? device first installed or during instrument periodictest. The incorrect usage of the function is likely to increase output error ofHART? device.

      打電話加微信QQ咨詢

      儀器儀表廠家 紹興中儀電子有限公司
      總機:0575-85118510 15088506679

      成熟丰满少妇激情,五月婷婷六月激情综合网站,国产偷抇久久一级精品,国产草莓无码视频